1U Blanking Panel, 4mm, for 10 Inch Racks
This is a solid 1U blanking panel that closes one open gap in the front of your 10 inch rack. It's 3D printed in 4mm black PETG here in Tewkesbury, and it's built to the same hole spacing as every rack part we make, so it lines up with anything of ours above or below it.
Leave a gap in the front of a rack and the air your fans are working to pull through your kit takes the easy route instead, in through the gap and round the outside of your hardware. A blank closes that route off. It also keeps dust off whatever sits below it, puts something solid between small fingers and live kit, and turns a row of gaps into one flat black front.
The edges, the lettering and the free hole
The front edge is slightly rounded, so it catches the light and you don't see a print line. The back is chamfered, so the panel sits flat against the rail instead of rocking on the little ridge a first layer leaves behind.
FOUR LAYERS is pressed lightly into the front, deep enough to read across a room and shallow enough to disappear at a glance. The part number is pressed into the back, mirrored, so it reads the right way round from inside the rack.
The panel fixes through the top and bottom holes of the U, so the middle hole stays free for something else.
Will it fit your rack?
There's no official standard for the outside width of a 10 inch rack, which is why we publish the hole spacing rather than a badge. Three things to look at on yours:
- The gap between the left and right mounting holes, centre to centre. This is the one that decides it, and you're looking for 236.525mm.
- The clear space between the rails. The panel is 249.0mm wide and has to drop in there.
- What the holes are: square slots, round holes with inserts, or a tapped thread. This decides your screws, not your fit.
Our holes are round rather than slotted. Slots would give a little wiggle room, but they'd also leave a visible gap round every screw and a panel that can sit slightly crooked, so we went for the clean front. That leaves about 0.3mm of float in each hole and no more, so a rack built well off the usual spacing won't take it.
On 9 August 2026 we took one panel off the printer and fitted it to two racks. First our own Four Layers Cube, which has square cage nut slots, where a cage nut can shift a fraction to help you. Then a Lab Rax style rack, where the holes are threaded metal inserts that can't move at all. It went into both with no filing and no persuading.
If you're not sure about yours, our fit guide walks you through the check in about two minutes. Or send us a photo of your rails before you order and we'll tell you what we think, even when the answer is no.
What's in the box
The panel. Screws, cage nuts and washers aren't included, because 10 inch racks don't agree on fasteners. Some take M6 cage nuts, some take M3 with butterfly nuts, some are tapped, and old imperial threads turn up too. A bag of the wrong screws is landfill, and your rack came with the ones it wants.
One thing worth knowing before you go rummaging in the spares tin. Hole position rarely catches people out. Screw length does. This is a 4mm plate, so on a rack with threaded inserts your screw loses 4mm before it reaches the rail. Add 4mm to what you'd use on a thin steel panel.
Why it's 4mm black PETG
A panel only has one job, which is to hold still while four bolts are done up through it. At 4mm thick, ours doesn't bow between the rails, and it doesn't go brittle round the fixings.
Every part we make is black PETG rather than PLA. A rack with kit running in it gets warm and stays warm, and PLA goes soft at temperatures a rack really reaches. Nothing melts. You just get a slow sag over months, until one day the panel above the switch isn't quite flat any more. PETG holds its shape, and it puts up with being unscrewed and screwed back in. It costs us more and prints slower, but that's our problem, not yours.
More than one gap
Racks tend to have gaps in the plural, and panels printed in the same batch match each other better than panels printed months apart. For three gaps there's the Homelab Starter Kit, three of this panel printed together. For four or more there's the five pack. It costs less than four single panels, so if you need four, buy five and keep a spare.
Every measurement, published
- Rack format: 10 inch
- Overall size: 249.0mm wide, 43.65mm tall, 4.0mm thick
- Rack unit: 1U, so 43.65mm of panel inside a 44.45mm unit
- Horizontal mounting hole centres: 236.525mm
- Vertical mounting hole centres: 31.75mm
- Which holes it uses: the 1st and 3rd hole of the U, middle hole left free
- Fixings: four M6, one per corner
- Hole type: round, not slotted, with about 0.3mm of float per hole
- Corner radius: 6.0mm
- Front edge: 1.0mm rounded
- Back face: 0.8mm chamfered
- Lettering: FOUR LAYERS pressed 0.6mm into the front, part number pressed into the back, mirrored
- Material: black PETG
- Made: in small batches by the two of us in Tewkesbury, Gloucestershire
- Model code: FL-BLANK-1U
What you're buying is the finished part, ready to bolt in, matched to every other rack part we make, with two people to email if anything's wrong.
Free UK postage, out in a day or two, and 30 days to change your mind on top of your 14 day right to cancel.