2U rack mount shelf from the front, with FOUR LAYERS running up the left side, a rack ear at each end and the slatted floor behind

2U Rack Mount Shelf for 10 Inch Racks (Routers and Small Boxes)

£28.50
Skip to product information
2U rack mount shelf from the front, with FOUR LAYERS running up the left side, a rack ear at each end and the slatted floor behind

2U Rack Mount Shelf for 10 Inch Racks (Routers and Small Boxes)

£28.50

This is a plain shelf for a router, or any other small box that never came with a rack mount of its own, in two units of your 10 inch rack. It was made with a FRITZ!Box 7530 AX in mind, and the details below give the biggest box it takes.

The front's left open, with FOUR LAYERS running up the left side. There's no solid floor. The box stands on slats running front to back, with open air between them, and two X braces underneath keep the shelf square. The side rails have hexagon cut-outs, and six fins across the back each take a cable tie.

A low lip across the front holds the box, so you can pull a cable out one handed and leave it where it is. Hook and loop straps go over the top to hold it down, and there are three places along each side rail to fit one, so a short box and a long one both get a strap across them. There's no stop at the back, because boxes come in all depths, so it's the straps that keep a box in place when you push a plug in.

The straps aren't included. It takes the common hook and loop cable straps, and the details below say exactly which size.

It bolts in on the same four M6 holes as our panels, so it lines up with anything of ours above or below it. There's a rear support bar in the box too. It bolts across your rack's back rails and the back of the shelf rests on it, so the shelf's held at both ends. The shelf itself only screws in at the front, and slides straight out towards you once those four screws are out.

We made it to fit FRITZ's own published size for the 7530 AX, but no real box has sat on it yet. If you'd like to check yours against it first, message us before you buy. We'd much rather answer a question than take a return.

The details

  • Rack format: 10 inch
  • Rack spaces: 2U
  • Holds: a router or other small box, up to 203.5mm wide and about 77mm tall
  • Made to fit: FRITZ's published size for the FRITZ!Box 7530 AX, 200mm wide, 152mm deep, 45mm tall
  • Fit: not yet tried with a real box
  • Front: open, with a low lip along the bottom and FOUR LAYERS running up the left side
  • Floor: none, the box stands on slats running front to back
  • Holding it down: hook and loop straps over the top of the box, with three places along each side rail to fit one
  • Straps: not included. It takes hook and loop straps up to 13mm wide and 2.5mm thick, such as the common 12.5mm one wrap cable strap.
  • Bracing: two X braces underneath
  • Side rails: hexagon cut-outs along both
  • Cable tidy: six tie fins across the back
  • Mounting hole centres: 236.525mm left to right, four M6 holes
  • Material: black PETG
  • In the box: the shelf and a rear support bar. Straps aren't included. Screws, cage nuts and washers aren't either, because 10 inch racks don't agree on fasteners.
  • Made: in small batches in Tewkesbury, Gloucestershire
  • Model code: FL-SHELF-2U-STRAP

This shelf goes out with its support bar, so for now it can take a bit longer to reach you than our panels do. If you need it by a certain day, message us before you order and we'll tell you where we are.

Free UK postage, and 30 days to change your mind on top of your 14 day right to cancel.

You may also like