Will it fit? A 10 inch rack compatibility checklist

The Four Layers Cube from the front and above with nothing fitted: two carry handles and a round hole in each corner of the top, and the open front with its rails and the bottom deck below

Two racks can both be sold as 10 inch and take completely different parts. That's not a scandal, it's just what happens when a format grows up without a standard. This is the check that tells you which sort you've got, in about two minutes, with a tape measure and no arithmetic worth the name.

Five things that change from one 10 inch rack to the next

Nobody's obliged to agree on any of these, so every maker settles them for themselves. Four of them decide what you buy. One of them decides whether anything fits at all.

1. The hole spacing. Measured centre to centre, left rail to right rail. It's usually 236.525mm, because that's what the 10 inch world has settled on by habit. Sometimes it isn't. This is the one you can't work around, and it's the first thing to check.

2. The hole itself. Three kinds turn up. A square cage nut slot with nothing in it, ours are 9.5mm by 9.5mm. A round hole with a threaded metal insert pressed into it. Or a rail that's simply been tapped straight through. Each one wants different hardware.

3. The thread. M6 is the common one. M3 with a butterfly nut on the back shows up on smaller printed racks. The imperial 12-24 and 10-32 turn up on anything with 19 inch ancestry in it.

4. The clear space between the rails. Not the holes this time, the air. A panel has to physically drop into that gap, and agreeing about hole positions isn't the same as fitting through the space.

5. The depth. Makes no difference at all to a panel. Makes an enormous difference to a shelf, a tray or anything with a floor, so measure it before you buy one of those.

Only the first one can stop a panel dead. The other four change which screws you order or which shelf you order, and those are mistakes you can walk back from.

The check, step by step

Step 1: pick any pair of holes Left rail and right rail, same height, anywhere up the rack. It genuinely doesn't matter which pair you use.

Step 2: measure centre to centre You want 236.525mm. Within about half a millimetre of that and you're fine. If the reading is somewhere completely different, stop here, because no 10 inch panel is going into that rack whoever makes it, and what you've probably got is a different format sold in similar language.

Step 3: measure the clear gap between the rails Rail face to rail face, with nothing in the way. Our panel is 249.0mm wide and it has to fall into that space rather than be persuaded into it.

Step 4: look properly at one hole Square slot, round hole with a metal insert, or a thread cut into the rail. Write down which one you've got. This decides your fasteners, not your fit, and it's the difference between a ten minute job and an order from a fastener supplier.

Step 5: work out screw length before you order screws This is the step almost everybody skips and it's the one that costs an evening. A printed panel is thick. Ours is a 4mm plate, so on a rack with threaded inserts the screw spends 4mm of itself just crossing the panel before it reaches the first thread in the rail. A screw that was ideal on a thin steel blank will find almost nothing to bite on. Add 4mm to whatever length you'd have used on steel.

Step 6: if anything came out odd, don't guess Photograph the rails with the tape measure laid across them and send it to us. One of us reads it and answers, and sometimes the answer is that ours won't fit your rack. That's a better email to get than a parcel you have to send back.

Send us a photo of your rack

Where our panels stop

Our mounting holes are round rather than slotted. A slot would give us room to be slightly wrong, and it would give you a visible gap around every fixing and a panel that can hang a little crooked. We went for the clean front instead.

What that costs is adjustment. There's about 0.3mm of float per hole, so a rack that's out by roughly 0.6mm in total will still take a panel, and anything past that won't go in. There's no slot to swallow the error, so nothing rescues it. On a five pack that arithmetic matters five times over, which is worth two minutes of your evening before you order one.

So we don't claim ours fits every 10 inch rack, and it's worth being a bit wary of anyone who does. We publish the spacing we built to. We put the same unmodified panel into two racks with two completely different fixing systems on 9 August 2026, our own rack with square cage nut slots, then a Lab Rax style rack with threaded inserts that can't shift a hair to help you. It went into both. If your rails are within about half a millimetre of 236.525mm, you're fine.

The racks people ask us about

We keep two lists. Racks we've actually had a panel in, and racks we only get asked about. Nothing moves from the second list to the first because it probably works, it moves when one of us has had it on the bench with a panel in our hand, and we put the date next to it. Both lists live on the Will It Fit page and they change as we get through them.

The racks we've tested, and the ones we haven't

One more thing, then you're done

Hole spacing decides whether the panel fits. What you almost never think about until the panel's in your hand is what holds it there. Ten inch racks don't agree on fasteners any more than they agree on width, which is why nothing comes in our box except the panel, and why there's a whole separate guide about it.

Which screws does your 10 inch rack take?

Measured, and it matched?

Then it fits, it's in stock, and it's out in a day or two with free postage anywhere in the UK. Racks tend to have gaps in the plural, so if you're closing more than one, the five pack comes off a single batch and one spool and matches all the way down the front. And if a tape measure isn't your idea of an evening, send us the photo instead. We'd much rather answer a question than take a return.

See the panel

Send us a photo of your rack

Before you go

Every guide here exists because somebody emailed and asked. If yours is not answered, ask it, and one of the two of us will answer.

Check it fits your rack Tell me when the next product lands