Nobody ships a bag of screws with a 10 inch rack panel, us included, and there's a reason for it that takes about a minute to explain. Here are the three kinds of hole you'll meet, the threads that go with them, and the length mistake that catches nearly everybody the first time they bolt a printed panel into anything.
Three kinds of hole, and yours is one of them
Open the front of your rack and look hard at one rail. Whatever else varies between racks, and plenty does, the hole in front of you is one of these three.
Square cage nut slots
A square hole with nothing in it. The thread comes as a separate part: you squeeze a cage nut into the slot from behind so it clips in and sits there, then drive a bolt into it from the front. Ours are 9.5mm by 9.5mm, which is the size you'll find on most racks that work this way.

The useful thing about a cage nut is that it cheats on your behalf. It sits a fraction loose inside its square hole, so it can shuffle a little to meet a bolt that isn't perfectly on centre. That forgiveness is real, and it's why a rack like this is the easy one to live with.
Round holes with threaded inserts
A round hole with a metal insert pressed into it, threaded already. The screw goes straight in. No separate nut, nothing to hold behind the rail with one finger while you hunt for the bolt with the other hand, which is a genuinely nicer way to spend a Sunday.
The catch is that an insert can't move. Not a hair. So either the holes in your panel line up with the rail or they don't, and this is the rack that finds out whether a part was drawn properly or just drawn optimistically. It's the reason we tested our panel against one.
Tapped rails
The same idea as an insert without the insert. The thread is cut directly into the rail. Screw goes in, job done, and it's every bit as unforgiving about alignment as an insert is.
Thirty seconds of looking settles which one you've got, and it's worth the thirty seconds, because the three want completely different hardware and only one of them needs anything extra buying.
The threads you'll meet
M6
The common one on 10 inch racks, and what our panels take. Four fixings per panel, one at each corner. If your rack came with a bag of bolts and cage nuts, this is very likely what's in it.
M3
Turns up on smaller printed racks, usually with a butterfly nut on the back so you can do the whole thing up with your fingers and no tools at all. Perfectly good system, completely different shopping list.
12-24 and 10-32
Imperial threads, inherited from the 19 inch world along with the rack unit. If your rack has 19 inch ancestry anywhere in it, these are what it'll want. They aren't M6 and they won't behave like M6, so match the rack rather than the spares tin.
Between three hole types and four threads in common use, there's no bag of fasteners we could put in a box that would be right for most people. A bag of one kind is the wrong kind for nearly everybody, and a bag of every kind means you paying to post screws you'll never take out of the packet. Your rack came with the ones it wants. If it didn't, or they've gone the way rack screws go, they're a few pounds from any fastener supplier once you know what to ask for.
The mistake almost everybody makes once
Hole position hardly ever catches people out. Screw length does, and it's the actual reason this guide exists.
Here's the only sum on the page. Our panel is a 4mm plate. On a rack with threaded inserts or tapped rails, the screw has to cross those 4mm before it reaches the first thread in the rail. Four millimetres of screw, spent, doing nothing but getting through the panel.
A steel blanking panel is thin, so whatever length you had lying around for one of those will reach almost nothing on a printed panel. What you get is a screw that pulls up tight against the front of the panel with two threads of grip, feels absolutely fine, and stays fine right up until the day somebody leans on the rack. Add 4mm to the length you'd have used on steel and you're back where you started.
If you're skimming this page, that last sentence is the whole guide.
What's in our box, and what isn't
In the box
- The panel. Five of them, if you bought the five pack.
Not in the box
- Screws, cage nuts, washers
That's a decision rather than a saving. Look back up this page: three hole types, four threads, and no way for us to guess which pair sits in your rack. So the panel arrives on its own, and this guide arrives with it.
One thing worth knowing while you're ordering fasteners for it. Our mounting holes are round rather than slotted, so there's no adjustment in the part. About 0.3mm of float per hole, roughly 0.6mm of error across the panel in total, and past that a different screw doesn't help you because the problem was never the screw. Checking the rack takes two minutes and it's worth doing before you order the panel, never mind the screws.
The full fit check, step by step
Right hole, right thread, right panel
Once you know which hole you've got and which thread goes in it, the rest of this is a ten minute job with a screwdriver. The panel's in stock, made in small batches here in Tewkesbury, out in a day or two with free UK postage. Racks tend to have gaps in the plural, so if you're closing more than one, the five pack comes off a single batch and one spool and matches all the way down the front. And if you're still not sure what you're looking at on that rail, photograph it and send it over. We'd much rather answer a question than take a return.