10 inch rack dimensions: every measurement that matters

Made to the numbers on this page

Everything here is drawn to 236.525mm mounting hole centres. If you're adding to a rack you already own, measure yours against that first. The guide below shows you how.

Four Layers Cube, three-quarter view showing both sides

The Four Layers Cube. £72.50

5U · black PETG · flat pack, brass fitted

See the Cube
The 1U blanking panel at an angle, showing the textured finish of the black PETG along its length

1U Blanking Panel, 4mm. £8.50

1U · black PETG · 3 for £22.50, 5 for £28.00

See the panel
1U Mac mini tray from the front, a black honeycomb face with FOUR LAYERS across the middle and the open floor behind it

1U Mac mini Tray. £25.00

1U · black PETG · M1, M2, M2 Pro, Intel 2018

See the 1U tray
2U open front Mac mini tray from the front, with FOUR LAYERS running up the left side and the round opening in the floor

2U Mac mini Tray, Open Front. £28.50

2U · black PETG · M4, M4 Pro

See the 2U tray
Which Mac mini tray? See everything we make
The front of the Four Layers Cube seen straight on, with a 1U panel screwed across the two rails, the two carry handles on top and the bottom deck below

Somebody will tell you a 10 inch rack is a standard size. It isn't, and nearly every fit problem in this hobby starts with that assumption. So here's every measurement that matters, where each one actually comes from, and the single number that decides whether the part you're about to buy will bolt up.

There is no 10 inch rack standard

Let's get this one out of the way first. There's no published standard for a 10 inch rack. No committee, no document, no number a maker was obliged to hit and no number you can hold them to afterwards.

The standard people are thinking of is EIA-310, and that one governs the 19 inch rack. It's real, it's old, and it's the reason a 19 inch switch made by anybody bolts into a 19 inch rack made by anybody else.

The 10 inch format borrowed one thing from it. The height of a rack unit, 44.45mm. Everything else, the width across the rails, the width of the box, the shape of the holes and what goes into them, got decided by whoever happened to be drawing a rack that week.

Which means that when a listing says "fits any 10 inch rack", nobody's necessarily trying it on. They just can't know.

Every number in one place

These are the figures worth having in front of you. The ones marked as ours belong to the panels and the rack we make, and they're here so you've got something real to compare your rack against instead of a number off a forum.

Measurement Figure What it's doing
One rack unit, 1U 44.45mm Borrowed from the 19 inch world. The only number the whole format agrees on.
Hole positions per U Three Most 1U parts use two of them and leave one spare.
Height of a 1U panel 43.65mm Deliberately shorter than the U it goes in.
Air above and below a fitted panel 0.4mm each That 0.8mm difference, split top and bottom, so panels stack without fouling each other.
Vertical hole centres 31.75mm On our panels, that's the 1st and 3rd hole of the U with the middle one left free.
Horizontal mounting hole centres 236.525mm Centre of the left rail hole to centre of the right. This is the one that decides fit.
Our panel width 249.0mm Has to physically drop into the clear gap between your rails.
Our panel thickness 4.0mm Matters for screw length and for almost nothing else.
Our rack's outer shell 264.525mm Somebody else's 10 inch rack will be a different width, and neither of us is wrong.
Square cage nut slot 9.5mm by 9.5mm On racks that fasten this way, ours included.

One thing the table can't say for you. Nothing on a 10 inch rack reliably measures ten inches. Not the rails, not the box, not the panel. "10 inch" is a family name rather than a measurement, so buy on the hole spacing and never on the name.

See the panel these numbers describe

Which of these you can trust

Split that table in two and the whole thing gets easier to hold in your head.

The vertical figures are steady. 44.45mm per U came straight out of the 19 inch world and nobody's felt the need to argue with it since, so a 1U gap is a 1U gap wherever you are. The 43.65mm panel height follows from it, and so does the three hole positions per U. If you're buying by height, you're on safe ground.

The horizontal figures are habit rather than law. 236.525mm between the mounting hole centres is what the 10 inch world has quietly settled on between itself, and most racks worth owning are built to it. Some aren't, and strictly speaking they haven't broken a rule by not being.

Then there's outside width, which is nobody's business but the maker's. Our own shell measures 264.525mm across. Yours will be something else. Panel widths vary the same way and for the same reason, so a panel width in a product listing tells you very little about whether that panel goes in your rack.

The one measurement to take on your own rack

If you do one thing after reading this, do this one. Find a mounting hole on the left rail and the hole opposite it on the right, at the same height. Measure centre to centre.

You're looking for 236.525mm. Anything within about half a millimetre of that and you're fine. If your tape lands somewhere close, good, you own a rack built to the spacing everybody else is drawing against. If it lands somewhere else entirely, stop there, because no 10 inch panel from anyone is going into that rack, and the usual explanation is that it isn't a 10 inch rack at all but a different format sold in similar language.

Everything else on that table is secondary and here's why. Panel height is the same everywhere, so it can't catch you out. Panel width only has to clear the gap between your rails, and a millimetre either way makes no difference to that. Depth never touches a panel at all. Hole spacing either lines up or it doesn't, and there is nothing you can do at the rack to talk it round.

Two more things worth writing down while you're stood there with the tape. The clear space between the rails, because the panel has to fall into it. And what the hole actually is: a square slot, a round hole with a threaded insert, or a thread cut into the rail. That second one decides which screws you buy rather than whether the panel fits, and it's the question we get asked most after this one.

The full step by step check

Which screws does your rack take?

What our own numbers won't do for you

Our mounting holes are round rather than slotted, which means there's no adjustment in the part. About 0.3mm of float per hole, so roughly 0.6mm of error across the panel in total, and past that nothing rescues it.

So we don't say our panels fit every 10 inch rack, and you should be a bit suspicious of anyone who does. We publish the spacing we built to, we bolted the same unmodified panel into two racks with completely different fixing systems on 9 August 2026, and if your rails are within about half a millimetre of 236.525mm you're fine.

Measured, and it matched?

Then the only questions left are which screws and how many gaps. Both have their own guide, and both take less time than the measuring did. If you'd rather skip the tape measure altogether, photograph your rails and send it over. One of us will read it and tell you, including when the answer is that ours won't fit.

As for the gaps, count them in U. Three is the Homelab Starter Kit, and five is the 5 Pack, which comes off a single print run so the black matches.

Check your rack in two minutes

Tell me when the next one lands

Before you go

Every guide here exists because somebody emailed and asked. If yours is not answered, ask it, and one of the two of us will answer.

Check it fits your rack Tell me when the next product lands